The rubber gasket that runs around the face of the boss is made from 4 flat strips of rubber 1.5mm thick. The enclosure and lid then received 1 coat of undercoat and a few coats of Battleship. It’s actually really good quality spray paint - and only $6.99 a can! I also found the same spray paint at an art shop called Eckersleys (although it was $9.99 here. The paint colour used for the enclosure is `Battleship Grey’ and after much searching I found a brand of spray paint called `IronLak’ at Officeworks (that had a colour called `Battleship’. The corners are shaped from solid blocks of pine and all are fixed in position using PVA adhesive. The lid front face and sides are made from 3mm MDF. These are to hold the backing board in position. On the other side is an M5 nut which gets fixed into a counterbored hole (concentric with the Ø6mm hole) with two-part epoxy adhesive. In each corner of the enclosure is a square of 12mm MDF with a Ø6mm hole in it. It’s amazing how good the inside fillets look using this method! You can then sand the filler with a piece of sandpaper wrapped around a dowel with a slightly smaller radius. All outside fillets can be achieved with careful sanding, and to get the inside fillets I applied some ready-to-use multipurpose filler with my little finger. The boss on the front face is made from pieces of 20 x 8mm moulding. For extra strength I fitted 12 x 12mm mouldings all around the inside of the side panels. The four side panels are cut from 3mm MDF and fixed into position on the back panel using PVA adhesive. To make the Enclosure I cut the shape for the back panel from 6mm MDF. The Enclosure is basically a deep, rectangular box with two small mounting flanges top and bottom and a wide `boss’ all around the front face. sheet could now easily be determined from my drawing. sheet and created my own drawing from that. I did find them on another site for around $130, but I decided to make my own enclosure instead. This way, you can swipe left or right on your Apple Watch to switch between synced watch faces anytime.Īnd you’re all set! If you have questions about whether Clockology will drain your watch battery, this FAQ should help.During my research I found out that the enclosure is a Stahlin J1210HPL and on their website these cost around $170 + postage. To load up any desired watch face to your watch, simply hold down on the watch face and select the “Watch Sync” option.įor every watch face sync, be sure to deselect the “Replace Clocks” option. These are a bunch of watch faces you can sync to your watch. You should then see an “Example Clocks” folder with 115 items. Head to “Browse”, and type “Clockology” in the search bar. Now you’re ready to install your custom watch faces. You should see the pink circle watch face with the word “Beta”. Tap and hold your finger on it, and select “Watch Sync”. Now you should see a big pink circle watch face with the word “Beta” in the centre. Once it is downloaded, hit the downloaded file and it will open up your Clockology app. Next, you’ll need to open up your web browser on your iPhone and download a “_EnableBeta” file. Change the “ON TAP” setting to “Wake for 70 Seconds” and “RETURN TO CLOCK” setting to “After 1 hour”. Within the Apple Watch app, head to “General”, and scroll down to “Wake Screen”. Now you’ll need to change some settings on your Apple Watch. If it doesn’t head to your Apple Watch app and scroll down to “Clockology” and make sure the “Show App on Apple Watch” is enabled. Head to the App Store and download the Clockology app.Īfter downloading the app to your iPhone, you should see it appear on your Apple Watch automatically. If you’re bored of the default watch faces on your Apple Watch (Series 5 & 6), and want to unlock the endless options made possible by the free Clockology app, here are the steps you’ll need to get started right away:
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |